Home page
SPONSOR AD

Support our Vendors!  |  Advertise Here

Topic: Fender Reinforcement Cable

in Forum: C3 Body


Already a Member?
Login
Not yet a Member?
Register for Free!

Fender Reinforcement Cable (1/6)
 7/24/13 8:39am
JPD1stVetteGold Member
Gold Member
Send Private Message

Scotch Plains, NJ - USA

Vette(s):
1981 Corvette Coupe, Stock, Black on Black, 4 Spd


Joined: 1/11/2006
Posts: 230

I am atempting to put some of the pieces back on the car.
I can't seem to locate the hole on the top of the dash panel to secure the cable.
Does anyone have any photos or know of any alternate locations for this hole?
I looked from the underside in the car but no hole!
Thanks
 
  


|UPDATED|7/24/2013 5:39:58 AM (AZT)|/UPDATED|


______________

Our Sponsors help support C3VR
Re: Fender Reinforcement Cable (2/6)
 7/24/13 12:31pm
DaveMLifetime Member
Lifetime Member
Send Private Message

Flanders, NJ - USA

Vette(s):
1982 Black, ZZ4, Hooker Side Pipes, 3.55 Rear, Rebuilt & upgraded 700R4, All new suspension, brakes, & new Charcoal interior.


Joined: 1/27/2004
Posts: 2552

My cable broke so I had to run a new cable. I went down from the top (under the hood) and attached the new cable to it and pulled it up that way.
Dave


______________

 

Lifetime Member #116
Dave's '82


   

Re: Fender Reinforcement Cable (3/6)
 7/24/13 12:44pm
Adams' AppleLifetime Member
Lifetime Member
Moderator
Send Private Message

Duncanville, TX - USA

Vette(s):
#1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas


Joined: 11/8/2003
Posts: 20128


I'm lost on this one....I have no clue what cable this is, or where it's s'pose to go.
Is there a larger diagram)or a pic) that shows a little more of the area?
What is the actual function of this cable?
Is this a late model('80-'82) thing only?
Will Lassie finally tell Timmy to go jump in the well?


______________

Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Re: Fender Reinforcement Cable (4/6)
 7/24/13 1:16pm
JPD1stVetteGold Member
Gold Member
Send Private Message

Scotch Plains, NJ - USA

Vette(s):
1981 Corvette Coupe, Stock, Black on Black, 4 Spd


Joined: 1/11/2006
Posts: 230

The sheet I referenced is entitled "Fender Reinforcement Cable, YA00 ALL".
It is not a ground cable for sure, measures about 5" long.
Yes, there is another sheet # UPC B01/BO12 Sheet 18 but I don't have it with me.
A photo would help.
Joel, all good questions


|UPDATED|7/24/2013 10:16:06 AM (AZT)|/UPDATED|


______________

Re: Fender Reinforcement Cable (5/6)
 7/24/13 2:08pm
F4GaryGold Member
Gold Member
Send Private Message

Grapevine, TX - USA

Vette(s):
1972 LT-1 convertible with factory air.


Joined: 8/26/2006
Posts: 1409

Never heard of this either.  Looks like it helps hold up the floor.  Beer

______________

   

Re: Fender Reinforcement Cable (6/6)
 7/24/13 3:27pm
DaveMLifetime Member
Lifetime Member
Send Private Message

Flanders, NJ - USA

Vette(s):
1982 Black, ZZ4, Hooker Side Pipes, 3.55 Rear, Rebuilt & upgraded 700R4, All new suspension, brakes, & new Charcoal interior.


Joined: 1/27/2004
Posts: 2552

My mistake, I thought you meant the hood release cable........never mind.
Dave


______________

 

Lifetime Member #116
Dave's '82


   

Our Sponsors help support C3VR