Home page
SPONSOR AD

Support our Vendors!  |  Advertise Here

Topic: Fan Hit Radiator Hose

in Forum: C3 Cooling and Heating Systems


Already a Member?
Login
Not yet a Member?
Register for Free!

Fan Hit Radiator Hose (1/8)
 6/10/07 12:41am
rearn2go72
Former Member

Send Private Message

Bladenboro, NC - USA

Vette(s):
1972 conv., sunfire yellow, blk interior, blk vinyl and convertible top. Off frame restoration with American Speed 383 stroker engine producing 500hp plus a 200hp NOS system. MSD ignition. Hooker super competition headers with chambered exhaust.


Joined: 1/22/2006
Posts: 1058

On the way home from a cruise-in I kept smelling something that smelled like a hot radiator. Kept my eye on the temperature gauge and it never got up to 200 degrees. When I got home and opened the hood it was obvious, as I had water all under the hood of the car. My fan had hit the bottom radiator hose, cutting it just enough to have a pin size stream of water shooting everywhere.

Now here's my question. Since I know my motor supports are good, what could have caused this? Anyone who has a 72 knows that you don't have but about 5/8 inch clearance between the fan and the bottom hose. I know my motor has a lot of torque (512lbs) but is it possible that the body would twist that much?
Our Sponsors help support C3VR
Fan Hit Radiator Hose (2/8)
 6/10/07 5:46am
dwright
Standard Member
Moderator
Send Private Message

Victor, NY - USA

Vette(s):
2004 Commemorative Edition Coupe, Auto w/HUD. 13K miles in 2015. Sold 1982 Red Coupe


Joined: 7/12/2004
Posts: 6833

Was the hose old and weak?
Could it have momentarily collapsed and hit the fan?
Did the sh*t hit the fan?
 
 
Sorry, couldn't resist.LOL


______________
 
Save the Wave!
Support the National Corvette Museum   
Fan Hit Radiator Hose (3/8)
 6/10/07 11:48am
Adams' AppleLifetime Member
Lifetime Member
Moderator
Send Private Message

Duncanville, TX - USA

Vette(s):
#1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas


Joined: 11/8/2003
Posts: 20126

Engine torque would not be an issue, I wouldn't think. More likely is the hose "flopping" as you drive. The hose will also expand under pressure, creating a larger target for the fan. Are you sure it was the fan that did it, or a belt?

______________

Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Fan Hit Radiator Hose (4/8)
 6/10/07 12:16pm
kstyerLifetime Member
Lifetime Member
Moderator
Send Private Message

CUYAHOGA FALLS, OH - USA

Vette(s):
1975 C3 Red, T-Tops, Black Interior. All I need is time and money! Getting there!


Joined: 12/2/2003
Posts: 6424

Any wear or deteration on the hose can make it loose it's ability to hold itself in position.   Watch when installing a new hose, if it's twisted just a bit, your clearance goes away.
This is not a rare thing.  It's just something that needs to be watched as part of preventive maintance.   Tough way to learn.
Fan Hit Radiator Hose (5/8)
 6/10/07 8:46pm
rearn2go72
Former Member

Send Private Message

Bladenboro, NC - USA

Vette(s):
1972 conv., sunfire yellow, blk interior, blk vinyl and convertible top. Off frame restoration with American Speed 383 stroker engine producing 500hp plus a 200hp NOS system. MSD ignition. Hooker super competition headers with chambered exhaust.


Joined: 1/22/2006
Posts: 1058

No Dwight, the hose wasn't old and weak but the sh*t did hit the fan. I have one heck of a mess all over my engine now.

Joel it had to be the fan because it's the lower hose and no belt close by. After replacing the hose yesterday, I noticed before even starting the car up that I only have between 1/2 and 5/8 inch clearance between the hose and fan. It was definitely the fan because the paint is off the tips of the fan. I hadn't even thought of the hose expanding under pressure. Since I've never had a shroud on the car and it runs a littler warmer  than I like, I'm just going to order the duel spal fans. That will definitely eliminate the possibility of this happening again.
Fan Hit Radiator Hose (6/8)
 6/10/07 9:41pm
Okie DudeLifetime Member
Lifetime Member
Send Private Message

Eastern Oklahoma County, OK - USA

Vette(s):
1980 Black L48 T-Tops


Joined: 1/3/2006
Posts: 1560

Alternatively, you could get the universal hose with the spring installed.  It is a B!tch to install, but it is a stiff hose.  When the paint guy was pulling out my A/C stuff for me (who needs A/C in a T-TOP car?) he noticed the A/C hose had rubbed a wear spot on the lower hose.  I'll have to change it when I get her home (if I ever get her home, raining & storms all weekend).

The dual spal fans will definitely alleviate the problem.

Good Luck!
Fan Hit Radiator Hose (7/8)
 6/11/07 12:28pm
1969 L46
Former Member

Send Private Message

Jefferson City, MO - USA

Vette(s):
1969 L46 4 Speed Roadster


Joined: 3/9/2007
Posts: 150

The wife and I took the Vette on her maiden voyage on Saturday.  We cruised with the top down.  It was about 90 degrees with 85% humidity.  I have a big block size aluminum radiator with dual spal fans.  The temperature never got over 205.  It averaged around 190 for most of the 130 mile trip.  The fans only came on three times.  Loosing the steel fan and fan clutch will also free up a couple of ponies too.  I also used chrome plated stainless radiator hoses (no ruptures). 

Fan Hit Radiator Hose (8/8)
 6/11/07 1:10pm
JimGLifetime Member
Lifetime Member
Send Private Message

Gloucester, VA - USA

Vette(s):
1979 T-Top, Metallic Green ZZ4 350/355 hp 405 ft/lbs torque Dual Spal Fans 700R4 4 Spd O/D Transmission 2004 Z06 Commemorative Edition


Joined: 1/29/2005
Posts: 1453

The dual SPAL setup ROX ! I luv it !

______________

Lifetime Member #73

The Money Pit.... and my niece

(click to see a slightly larger version)

Our Sponsors help support C3VR