Home page
SPONSOR AD

Support our Vendors!  |  Advertise Here

Topic: Transmission Fluid Capacity

in Forum: C3 Driveline Components


Already a Member?
Login
Not yet a Member?
Register for Free!

Transmission Fluid Capacity (1/4)
 2/17/23 4:41pm
Kenny78Gold Member
Gold Member
Send Private Message

Toms River, NJ - USA

Vette(s):
1978 Silver Anniversary Coupe Lt. Biege w/ Dark Brown Int. Happily owned since 1981.


Joined: 7/28/2004
Posts: 115

Hi all,

Changed gasket & filter on the 350 Turbo Hydromatic. ( couple of weeks ago ). How many quarts of tranny fluid does it take?? So far, I have put 4 qts in and it doesn't register on the dip stick. 

Thanks,

Kenny78

Our Sponsors help support C3VR
Re: Transmission Fluid Capacity (2/4)
 2/17/23 10:56pm
Adams' AppleLifetime Member
Lifetime Member
Moderator
Send Private Message

Duncanville, TX - USA

Vette(s):
#1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas


Joined: 11/8/2003
Posts: 20129

4 quarts should have filled it, unless it was low to begin with, or the pan was off for an extended time, and more fluid than normal drained out. If in doubt, go ahead and add small amounts until it shows the correct fluid level. It's better to have a lil too much than not enough. 😉

Also...are you sure it has the correct dipstick & tube? 

 Here's a tip for everyone, and it is true for pretty much ANY auto trans with a removable pan. While you have the pan off doing a fluid change, or whatever, insert the dipstick fully into the tube, Then, mark the stick with a line(file, notch, whatever) LEVEL with the bottom edge of the pan rail on the trans. This is a true indicator of the needed fluid level when hot. This is helpful if you do not know the stick/tube is correct, or if you have one of the aftermarket tubes/stick assemblies....or any other issues. Sometimes, the sticks, or sticks and tubes get replaced, or lost, or just got something stuck in it to plug the hole. Marking the stick like this will give you the correct fluid level, with the fluid hot, regardless of the stick-tube combination. If the combo is correct for the trans, the mark you make will be just about in the center of the hash marked area of the stick. If it is not then now you have a correct level mark to use.  🤠

 

 



______________

Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Re: Transmission Fluid Capacity (3/4)
 3/3/23 3:49pm
Z06Frank
Former Member

Send Private Message

Gurnee, IL - USA

Vette(s):
1968 Coupe International Blue 427 2006 Coupe Metallic Silver Z06


Joined: 7/11/2022
Posts: 3

I re-gasketing and replacing the rear tail housing on my M20 4-speed trans for my '68 BB. No dipsticks (obviously) for this and if I remember correctly you fill to the inlet port height.

2 quarts on mineral oil based right????

Re: Transmission Fluid Capacity (4/4)
 3/3/23 4:02pm
F4GaryGold Member
Gold Member
Send Private Message

Grapevine, TX - USA

Vette(s):
1972 LT-1 convertible with factory air.


Joined: 8/26/2006
Posts: 1410

Z06Frank said:

I re-gasketing and replacing the rear tail housing on my M20 4-speed trans for my '68 BB. No dipsticks (obviously) for this and if I remember correctly you fill to the inlet port height.

2 quarts on mineral oil based right????


I've been told not to use synthetic so it's conventional for me.  Is that what you mean by mineral oil?



______________

   

Our Sponsors help support C3VR