Home page
SPONSOR AD

Support our Vendors!  |  Advertise Here

Topic: head gasket

in Forum: C3 Engines


Already a Member?
Login
Not yet a Member?
Register for Free!

head gasket (1/10)
 12/15/08 7:49am
mikeee
Former Member

Send Private Message

Oviedo, FL - USA

Vette(s):
1977 t-top


Joined: 9/8/2006
Posts: 267

Can anyone recomend the correct( or the best) head gasket to use on my 350.It will have vortec heads,mild cam,avg.compresion.

Our Sponsors help support C3VR
head gasket (2/10)
 12/15/08 10:58am
corvette440hpLifetime Member
Lifetime Member
Send Private Message

Joined: 7/2/2006
Posts: 8205

http://store.summitracing.com/partdetail.asp?part=NAL%2D10105117&autoview=sku  Check these out........they will work for you:

______________

corvette440hp
head gasket (3/10)
 12/19/08 3:18pm
mikepthree
Former Member

Send Private Message

Baldwinsville, NY - USA

Vette(s):
78 Silver L48 4Spd, dual exhaust, GM vortec head, Edelbrock intake, Crane 210/216 degree x .420/.454 lift, 180 thermostat, MSD street fire


Joined: 1/15/2007
Posts: 19

Hey Mikee,
I did a SPparts Vortec head change and they supplied the NAL-10105117 mentioned above, .028, GM gasket on a GM block & head.
Get the head clean and flat as you can, slowly place the head on the block, do not drop an edge and ding it.
Good luck and let us know how you made out.
MikeP3
head gasket (4/10)
 12/20/08 9:38am
78SEvetteLifetime Member
Lifetime Member
Send Private Message

Holland, OH - USA

Vette(s):
1978 Silver Anniversary Edition


Joined: 11/29/2004
Posts: 217

   I suggest that you use new head bolts and that you torque them in steps until you get the proper torque. For instance, if the torque is 100#, step one is to 70#, then step two is to torque them to 90#, step three is final value. It may take alittle longer, but you lessen the chance of warping the heads and you don't distort the gasket. You will get a better seal and have less chance of the bolts loosing up later. Hope this helps.

Jim

head gasket (5/10)
 12/24/08 7:59pm
Sarge81Lifetime Member
Lifetime Member
Send Private Message

WEST SENECA, NY - USA

Vette(s):
1981 Blue Ice Met. w/pearl ghost flames TKO500 5speed. LS1 Swap 3.45 Dana 44.


Joined: 12/3/2001
Posts: 2379

Fel-Pro Part#1094 is .015" thick.

 In the February issue of Hot Rod Magazine, they were testing different heads,cam,intake/carb on a ZZ4 engine. They mentioned they replaced the GM head gasket which measured .051" thick with the Fel-Pro gasket I mentioned above.
 I tried to look up the head gasket I have on my 350 HO crate engine which measure in at .017" thick. The GM part number is no good now. Now they only offer the one that is .028" thick.


______________

GEN III 5.7L "LS6" Engine swap
TKO500 5 spd.
3.54 Dana 44
'69 "N11" Sidepipes
Borgeson Steering Box
Born 8/1981
Sequence #3975




Click here to see more pics of my Vette on CarDomain.


Lifetime Member #26
head gasket (6/10)
 12/27/08 11:12am
mikeee
Former Member

Send Private Message

Oviedo, FL - USA

Vette(s):
1977 t-top


Joined: 9/8/2006
Posts: 267

No problem getting deck clean as possible,it's getting a few thousands cut when machine shop decks it and the vortec heads are new,Still haven't bought new ARP bolts,but will.
head gasket (7/10)
 12/28/08 12:05am
kstyerLifetime Member
Lifetime Member
Moderator
Send Private Message

CUYAHOGA FALLS, OH - USA

Vette(s):
1975 C3 Red, T-Tops, Black Interior. All I need is time and money! Getting there!


Joined: 12/2/2003
Posts: 6424

I use FelPro wheneve possible.  Just me.
Re: head gasket (8/10)
 1/12/16 11:50pm
my80Vette
Former Member

Send Private Message

Dacula, GA - USA

Vette(s):
1980 Corvette White and Black with Black interior. 350 V-8 Auto


Joined: 7/18/2015
Posts: 33

Not a good week! My son bought a 78 three weeks ago. On his way back to college on Sunday his alternator belt shredded and knocked the other belts off. He was on freeway and got off as quickly as possible but I don't think it was fast enough. It obviously overheated among everything else. After replacing the belts and antifreeze my worst fear happened lots of white smoke when starting the engine. Once driven for a few miles the smoke clears to normal. I also replaced thermostat as I could touch the radiator cap and it was cool to touch after driving for a few miles. It kept overheating and each time we would turn off and restart the smoke came back. So to make long story longer I took it to a local shop near his college that I hope is reputable and I'm waiting to hear from them. First question is if the block cracked in addition to the head gasket being blown should I have the block repaired or replaced? It is the original engine and tranny with 90k on it. Overall the car is mostly original but has headers and side pipes. Second question, and this is more for very future reference, how much does replacing the engine affect the value of the car. Thanks for any input.
Re: head gasket (9/10)
 1/13/16 1:53pm
Adams' AppleLifetime Member
Lifetime Member
Moderator
Send Private Message

Duncanville, TX - USA

Vette(s):
#1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas


Joined: 11/8/2003
Posts: 20126

At the worst, you'll prolly have a cracked head....it's really hard to do any real damage to the block, unless it's intentional. Be sure to have them check the valves, guides, & seats in the heads when they test them for cracks.

As far as a replacement engine effecting future value, it normally will, to some extent....just depends on who is looking to buy it. They may not care if it's 100% OE or not. 

Also, it's better if you start a new thread with any questions regarding your car(s), rather than post in an old thread, even tho it is somewhat related to your issue. It keeps your question(and any subsequent responses) yours, and the old thread author's his/hers. Tongue Thumbs Up


______________

Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Re: head gasket (10/10)
 1/13/16 4:33pm
F4GaryGold Member
Gold Member
Send Private Message

Grapevine, TX - USA

Vette(s):
1972 LT-1 convertible with factory air.


Joined: 8/26/2006
Posts: 1406

my80Vette said: Not a good week! My son bought a 78 three weeks ago. On his way back to college on Sunday his alternator belt shredded and knocked the other belts off. He was on freeway and got off as quickly as possible but I don't think it was fast enough. It obviously overheated among everything else. After replacing the belts and antifreeze my worst fear happened lots of white smoke when starting the engine. Once driven for a few miles the smoke clears to normal. I also replaced thermostat as I could touch the radiator cap and it was cool to touch after driving for a few miles. It kept overheating and each time we would turn off and restart the smoke came back. So to make long story longer I took it to a local shop near his college that I hope is reputable and I'm waiting to hear from them. First question is if the block cracked in addition to the head gasket being blown should I have the block repaired or replaced? It is the original engine and tranny with 90k on it. Overall the car is mostly original but has headers and side pipes. Second question, and this is more for very future reference, how much does replacing the engine affect the value of the car. Thanks for any input.

If it's a non Silver Anniversary or Pace Car, I wouldn't worry too much about original engine unless you are going to NCRS the car.



______________

   

Our Sponsors help support C3VR