Rod I hope this might help...............
How To Repair the Wiper Doors on your 1968-1972 Corvette
Vacuum-Operated Wiper Door Woes
Story and Photos by Chris and Stephanie Petris
One thing is for sure, the 1968-1972 Corvettes had cutting-edge technology. A vacuum-mechanical headlamp and wiper door with fiber-optic bulb status was undoubtedly innovative. It was quite an accomplishment to get the wiper door to close and open in conjunction with the wiper arms swinging around.
Certainly, fail-safe switches were incorporated to prevent inadvertent closing of the wiper door on the wiper arms. With the smooth transition from hood to windshield, the wiper door makes the 1968-1972 Corvettes unique in appearance and function.
The article featured on this page is from the May 2010 issue of Corvette Enthusiast Magazine.
Like our headlamp door res-toration story, the 1969s wiper door was corroded and stuck in the closed position. The wiper door was stuck so badly that we removed the entire assembly to avoid breaking components. All of the wiper door linkage pivot points are plastic-bushed, and the corrosion made the bushings stick. Once you get the door linkage pieces out, you will realize that it took a lot of thought to make all these strange-looking linkage pieces to make the door move so smoothly. Our linkage was in decent shape except for the corroded pins and bushings. The pivot pins are actually job-specific rivets that require setting with a press or hammer to stake the pin in tightly. Another problem that we always encounter, no matter how well-maintained the 68-72 Corvette, is stuck wiper door to linkage screw-in pivot pin bolts. Wiper door screw-in pivot pin bolts corrode and then break as you try to remove them. We find at least one tight screw per wiper door, and this 69 was no exception. All of the screws were tight and ready to break off. Every once in a while something goes right in our case, discovering that tapping on the backside of the pivot screws to loosen them actually works. The idea is to tap on the backside of the screw to loosen the corrosion and allow the screw to release the threads.
Once all the pieces are apart, we can start the clean-up process and prep for paint. Before any final painting occurs, we will assemble the linkage and stake the pins in place. This avoids chipping and scratching the paint. After staking the pivot pins, we will paint all the linkage pieces with good-quality black epoxy paint. We have easier access before the linkage components are re-installed, so lets move on to the vacuum system and installing the wiper arm switch and hoses.
A Systems Approach: The 68-72 wiper door vacuum system uses the same relay valve as the headlamp vacuum system with specific switches and two different style wiper door actuators. All 1968 and early 1969 wiper door actuators use a fiber piston seal that rides in the canister bore. Late 1969 wiper door actuators resemble a headlamp actuator with a captured rubber diaphragm in the center and an actuator shaft seal. The later wiper door actuator is very reliable, and if necessary, the actuator rod seal is replaceable. Due to their design, all early actuators have vacuum leakage by the fiber seal some more, some less. For instance, you can close off the back side of the later actuator vacuum connection, preventing any actuator rod movement, while the early actuator will let you move the actuator rod as the vacuum bypasses the fiber seal. The wiper door control system is more complicated than the headlamp system due to wiper door and wiper mechanism movement. 1968-1971 Corvettes control the wiper door vacuum solenoid through a relay, which was dropped for the 1972 model year. The 68-71 wiper relay was placed in the console area and is controlled by the wiper switch. The 1969-1972 Corvettes use the same vacuum control solenoid as the 1968-1971 without the relay. The vacuum solenoid is a simple device that opens, allowing vacuum to dump when 12-volt power is applied. The solenoids are reliable we see more damage from connector removal than solenoid failure. The connector must be carefully removed with side-to-side movement, or the terminal can be pulled out of the solenoid. 1969-1972 Corvettes use a vacuum switch on the wiper arm to prevent door closing until the wiper arm is fully parked. All of the wiper door systems use an override switch under the dash to bypass the relay (1968) and solenoid. The vacuum solenoid receives a signal from the wiper switch to route vacuum to the vacuum relay valve. Like the headlamp system, the relay valve sends vacuum to the wiper door actuator. All 68-72s have an additional override vacuum switch under the dash to open the wiper door.
Problem Areas: Like the headlights, vacuum leaks are the major concern, with a few switches that come into play. The 1969-72 wiper arm switch is prone to failure from the harsh environment (sunlight, water, etc.). All of the headlamp and wiper door vacuum systems use a vacuum reservoir to supply ample vacuum for quick wiper door operation. The same driver-side rear inner fender reservoir is used for the wiper door and headlamp system. The common problems are wiper arm vacuum switch, relay valves, and poor hose connections. The easiest way to troubleshoot the myriad of vacuum components is with a good vacuum gauge and pair of needle-nose pliers. Caps and plugs help isolate one system from the others, which in many cases, must be done because you may have multiple leaks. You can have all the relay valves leaking for both the headlamps and wiper door, for example. If you have access to a vacuum pump (an A/C vacuum pump works well), you can troubleshoot the system without the engine running to listen for audible leaks in the systems. If you are using the engine or an external vacuum source, you first need a baseline vacuum reading. This can be done by removing the vacuum source rubber hose and connecting the vacuum gauge to the engine if you are using engine vacuum. If you are using an external vacuum source, connect your gauge directly to the pump for the baseline reading. The next step is to tee the vacuum gauge into the vacuum system close to the source to begin leak checking. Then move outward on the vacuum source hose, clamping it with the needle-nose pliers until you see a rise in vacuum. If you are working with a 68-72 car, start by eliminating the headlamp vacuum system by plugging the supply line at the headlamp relay valve. If the vacuum reading rises, you know you have a leak at the front in the headlamp area. If the vacuum reading stays the same, plug off the wiper door vacuum supply hose and see if that makes the vacuum rise. You should be within an inch or two of the first vacuum reading when all the ports were blocked. What we need to know: Is the vacuum leak from a leaking relay valve or actuator? Since relay valves are prone to leaking, we can easily test them by plugging the green and red outlet ports. A good relay valve will have the vacuum rise close to the baseline vacuum. If it is down more than two to three inches of vacuum, the relay is bad. To save multiple part orders, you can use a vacuum splice connector to bypass the relay valve connecting the red vacuum actuator hose to the yellow supply hose to check for a vacuum loss. If you find a leak, the actuator diaphragm or the canister has a perforation. Actuator replacement is the only answer at this point. This same test can be done with the green actuator hose and the yellow supply hose. The green actuator hose is the push side that opens the headlamp or wiper door. Finding a leak on the green side of the actuator usually means the replaceable actuator rod seal is leaking. If there are no significant vacuum leaks and the headlamp doors do not work, you can apply vacuum to the relay valves small vacuum control port to see if the headlamps operate. You should find vacuum at the small hose when the headlamps are on. If no vacuum is found, look inside the car for the problem. If you found vacuum at the small hose, the relay valve is the problem. That is, of course, if the headlamp doors are not mechanically binding.
Do not be surprised if you find both of the systems leaking. Careful troubleshooting and repairs will get rid of the leaks, and you will even enjoy better engine performance. You will not be able to adjust the carburetor(s) to compensate for headlamp and/or wiper door vacuum for leaks that occur at the intake manifold. You can try to compensate for the vacuum leaks by adjusting the carburetor idle screws richer; but remember, the vacuum loss is after the carburetor so poor performance will result.
Inside Challenges: The cockpit vacuum system also has a myriad of hoses to contend with, but the difference is that they do not affect engine performance. Cockpit vacuum leaks are usually minor but significant because they operate at low volume, so any loss of vacuum can affect proper operation of the headlamps or wiper door. The headlamp control is simple; vacuum is supplied to the headlamp switch, and the headlamp switch routes vacuum to the headlamp door relay valve. The wiper door control is more involved and utilizes an electric vacuum dump solenoid that the wiper switch electrically controls. Both the headlamp and wiper door controls have an override switch to manually dump vacuum for wiper blade or headlamp replacement.
Cockpit vacuum problems usually occur after dash repairs have been performed because a vacuum hose is knocked off or broken. Original vacuum hoses usually fit loosely because of age, making them easy to knock off. The hoses themselves are not subjected to the under-hood heat so they stay in good condition for quite a while. Once all the hoses and components are installed, adjustments come next. Remember that the wiper arm vacuum switch must be fully depressed to allow the wiper door to close; likewise, the wiper motor armature switch must be depressed fully to allow the wiper motor to run.
Like our headlamp vacuum system, the wiper door vacuum system was in total disrepair, requiring us to replace all the vacuum system components including the relay valve, wiper arm switch, and all of the hoses. The vacuum hose kit system came with clear instructions on what length hose and indicates what color stripe goes where. Look at the supplied instructions and vacuum hose diagram carefully to assure that the correct length/color stripe hoses are used. It is easy to grab the wrong hose and think that something is wrong with the length. Take a tape measure and measure the hoses first no cutting is required!
The Bottom Line: This is certainly a big step in driving the 1969 Corvette on long road trips. It is very nice to know that the headlamps operate without our under-the-car manual intervention. Having wipers that come on when you request them takes some apprehension away when we drive the 69. One thing is certain we will take the 69 Roadster on longer road trips in 2010. Who knows? Maybe it is time the Corvette makes the trip to Corvettes at Carlisle.
1 This trick works well: tap on the pivot bolt to loosen them for easier removal. These pivot bolts snap quickly, and then the real pain begins. Our door had two previously broken pivot bolts to contend with. Its worth taking the entire assembly out to avoid drilling out broken pivot bolts.
2 Our pivot points were all corroded and tight. No rust penetrant in the world would free this linkage assembly for smooth operation. We took plenty of photos of this assembly for a reassembly road map.
3 The work was tedious, but each stamped side of the rivet was drilled off for removal. Try to avoid the pot-metal supports while drilling so the new rivets will fit tightly.
4 Once the rivet is drilled, a center punch is used to tap the rivet out of the linkage arm. Some of the linkage arms required support while tapping the rivets out.
5 Once the new Zip Products rivet and bushings are installed, our specially-ground punch sets the rivet. Zip Products has a complete set of rivets and bushings for the entire wiper door linkage assembly. Care must be taken that the rivets are not crimped too tightly, causing the linkage pieces to bind.
6 Another trick here: tap on the outside of the wiper door actuator-adjusting sleeve to break loose the buildup of corrosion. Restraint is important. Too much force from the hammer and the sleeve can be distorted.
7 The freshened-up sleeve is used to couple the wiper door mechanism to the actuator. The sleeve has right and left hand threads, so you must start both threaded shafts at the same time. Dont forget to tighten the jam nut to lock the adjuster to the actuator.
8 We had to solder the washer tubes to the wiper arms with acid core solder. Unfortunately, we found out later that the tab was turned around 180 degrees and had soldered them away from the wiper blade.
9 Before the wiper door is installed, the wiper arm vacuum switch is installed. This vacuum safety switch prevents the wiper door from closing until the passenger-side wiper arm is in the park position.
10 New wiper door bumpers were installed to keep the door alignment correct and prevent rattles. These screws were the only ones that came out easily without any corrosion present.
11 The new wiper door pivot bushings are installed with lubricant to keep them from binding and to keep them in place while the pivot bolts are installed.
12 New wiper door pivot bolts are installed in the previously HeliCoiled wiper door. We install 10-24 HeliCoils in all wiper door pivot bolt holes, even if the threaded holes are perfect. HeliCoils are made from stainless steel and will not corrode like the original pot-metal threads. The wiper pivot bolts should be lightly tightened to avoid breakage.
13 Heres another switch stop adjustment that prevents wiper arm and door collision. This stop bolt presses the wiper motor armature power switch, allowing current to flow to the motor and turn the wipers on when the door is open fully.
14 The wipers and the wiper door have many adjustments to balance out for proper operation. These 3/8-inch nuts are loosened to move the driver and passenger-side wiper linkages. The adjustment will move the wiper arms in towards the center or out towards the windshield trim.
15 This screw on the wiper blade arm is for moving the blade side of the arm in or out. We always install the wiper arm assemblies and check both the linkage and blade adjustment with the wipers on high speed. There is a fine balance between the blades crashing into each other and scrubbing the windshield trim.
16 You literally get to touch every area when the headlamp and wiper vacuum system are involved. This photo gives you an idea of what goes on behind the dash. The tach is on the right with the wiper door vacuum solenoid in place; the center vacuum switches override the wiper and headlamp switch operation.
17 We put together the under-dash hoses, then pushed the white-striped headlamp vacuum control into the grommet. The grommet is installed from under the dash. Permatex Super Lube is used to grease the hose to make it go through the grommet easier.
18 We found our tach cable in rough shape. Now is the time to replace it. The trick here is to connect the tach cable to the tach and once the dash panel is in place, connect the cable to the distributor.
19 While the dash panel is out, we decided to replace the 2.0 candlepower bulbs with 3.0 candlepower #1891 bulbs for brighter instrumentation. Push the bulb holder to the side to release it from the gauge. These bulb holders usually pop the center out of the plastic holder if you get rough with them.
20 The blue vacuum hoses connect to the bottom of both override switches. The upper red vacuum hose connects to the wiper arm switch in the cowl area and the white hose connects to the headlight relay valve. The loose yellow hose connects to the wiper solenoid.
21 The wiper cowl grille is an integral part of the wiper door linkage, stabilizing the linkage supports from the driver side to the passenger side. The 8-32-inch thread screws should be black oxide coated. Ours are stainless steel.
22 This vacuum check valve prevents unintended headlamp or wiper door operation under wide-open throttle situations. The small hose supplies vacuum to the cockpit vacuum switches controlling the headlamps and wiper door.