C3 Vette Registry - The Best Resource on the Net for C3 Vettes! C3 Vette
Forums -> C3 General Discussion
Not Logged In! Login or Register!  Users Online: 15 / Help 
Features  Find C3 Parts on ebay in only 2 or 3 clicks!  | Add YOUR C3 to the Registry

Supporting Vendors
Mid America Motorworks
Bair's Corvettes
Volunteer Vette Products

C3 of the Month
None Current
Enter Yours Today!
Online C3 Show
C3s are Registered

Vanity Plates
Featured Links

Buy Now
The Corvette Factories: Building America's Sports Car (Hardcover)
The Corvette Factories: Building America's Sports Car (Hardcover)

Collector's Originality Guide Corvette 1968-1982 (Paperback)
Collector's Originality Guide Corvette 1968-1982 (Paperback)

The Corvette Dynasty (Hardcover)
The Corvette Dynasty (Hardcover)

Corvette Fifty Years (Hardcover)
Corvette Fifty Years (Hardcover)

| Hide Signatures and Profile Pics

 New Topic New Topic Post Reply Reply New Poll New Poll Search     Search Page [1]  
10/14/16 11:36am - Original Message: '1968 327 complete ignition shielding proceedure'
Limited Member
- Send Private Message

cottonport, LA - USA

1968 conv. 36,000 org. mi. 2005 conv. 50,000 orig. mi.

Joined: 8/19/2016
Posts: 1
4 years ago i disassembled my 1968 327 vette engine. at the time it had all of the ign. shielding. I have since been in an accident and am suffering some brain trauma, and some memory loss due to the accident. when i took it apart i took pictures of all shielding and it's sequence of how to reinstall all of the pieces. The camera was stolen out of my wife's car. I have the original assembly manual, but there is only 1 scribble looking drawing and only lists the pieces. Does anyone have complete pictures how to put all these pieces back together, where they go again, wing nuts, bolts shapes on which side heat shields and where they bolt. I think some of the parts bolt onto the exhaust  and or the block but don't remember where that particular double looking bolt goes to do this. Please any help is appreciated. pictures, video, or instructions with diagrams. engine is back together, stopped short of exhaust and carb. really think chrome goes on before installing. i thing it would be too tough a job trying to get it right with engine in car. PS. this is a 36,000 mile original, mint condition, matching numbers car with 1 spray paint. ( son is a painter, and we are going to paint it back original type paint) I have protecto plate, order sheet, window sticker, tank sticker and i think pictures of the collections this car was in. 1 owner even had it in a bubble. I went through engine to make sure everything was correct, so that there would be no surprises. Everything was OK and now it really needs to be put back in car. THANKS flattopalpha@yahoo.com
 Reply Reply  Quote Reply w/Quote
Support C3VR!
Suport our advertisers
10/16/16 1:50pm - Reply: 'Re: 1968 327 complete ignition shielding proceedure'
Standard Member
- Send Private Message

Gig Harbor, WA - USA

1973 L82 4 Speed Coupe - Very original, well documented driver/survivor. 2016 Bend Regional NCRS Top Flight.

Joined: 10/2/2014
Posts: 401
Flattop, wish I had some great pictures or diagrams for you on the shielding but there's not alot out there. Some of the best diagrams I've found are in vendor catalogs. ZIP and Corvette Central have some decent diagrams that may help you out. Willcox Corvette may also have some diagrams or perhaps a video on their website, they have a lot of good "how to" material for C3 Corvettes. You are correct, putting the shielding on while the motor is out is the easiest but that same shielding must be removed and replaced to change the plugs and your not going to pull the motor back out for that. I would start by installing all of the shielding and brackets on the motor out of the car to sort out all of the correct components and their locations. I would then remove the upper chrome cover sections held on by the wing nuts to install the motor. Check out the diagrams in the catalogs mentioned above and see if they help out any. I have a few photos from my '73 that I could send you, they would be simular to your '68 but not exactly the same. Good luck !!

John Sigmund
NCRS Member 61302
NW NCRS Chapter Member

Duct tape is the new Black !!
 Reply Reply  Quote Reply w/Quote
 New Topic New Topic Post Reply Reply New Poll New Poll Search     Search Page [1]  
 Forums -> C3 General Discussion
(Moderator: Adam Wartell, Norsky, Adams' Apple)

Official C3 Vette Registry Community:
Home | Forums | Email | Who's Online | Clubs | Events | Member Stats

Other Official C3 Vette Registry Areas:
Members | Research | Shop | My Account | About C3VR

Corvette is a registered trademark of the General Motors Corporation(GM) & Chevrolet Motor Division. Vette Registries, LLC is responsible for all site content (except for member submitted content or where otherwise noted) and does not claim or imply that Chevrolet or GM is responsible for Official C3 Vette Registry content. Vette Registries, LLC is independent from GM and is not affiliated with, sponsored or supported by GM.  Copyright/trademark/sales mark infringements are not intended, or implied and are in fact used to support GM, Chevrolet and Corvette

Official C3 Vette Registry content is Copyright 2001-2018, Vette Registries, LLC. Content may not be reused without written consent. All Rights Reserved. NS

Corvette (Vette) Model Years on this site: 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 30