C3 Vette Registry - The Best Resource on the Net for C3 Vettes! C3 Vette
Forums -> C3 Handling Components
Not Logged In! Login or Register!  Users Online: 17 / Help 
Features  Find C3 Parts on ebay in only 2 or 3 clicks!  | Add YOUR C3 to the Registry

Supporting Vendors
Mid America Motorworks
VetteBookStore.com
Bair's Corvettes
CorvetteClothing.com
Volunteer Vette Products

C3 of the Month
None Current
Enter Yours Today!
Online C3 Show
13
C3s are Registered

Vanity Plates
71 GOLD
gold71
Featured Links
Chevrolet Corvette Restoration Guide


Buy Now
The Corvette Factories: Building America's Sports Car (Hardcover)
The Corvette Factories: Building America's Sports Car (Hardcover)


Chevrolet Corvette Restoration Guide
Chevrolet Corvette Restoration Guide


Corvette: America's Sports Car Yesterday, Today, Tomorrow (Hardcover)
Corvette: America's Sports Car Yesterday, Today, Tomorrow (Hardcover)


How To Rebuild Corvette Rolling Chassis 1963-1982
How To Rebuild Corvette Rolling Chassis 1963-1982



| Hide Signatures and Profile Pics

 New Topic New Topic Post Reply Reply New Poll New Poll Search     Search Page [1]  
3/1/12 1:55am - Original Message: 'rear brakes'
tomgaz
Former Member
- Send Private Message



Vette(s):
1975 chevy corvette coupe

Joined: 2/14/2012
Posts: 9
i am doing my first set of brakes on my first project car. It looks like one rotor has the rivets and one does not so i need a hand. How to drill out the rivets? what kind of bit do i need. the right rotor looks like the center of the rivets are drilled out the left side looks like they are solid. maybe a picture with them drilled out and a picture of them still their would help me out. thanks guys.
 Reply Reply  Quote Reply w/Quote
 
Support C3VR!
Suport our advertisers
3/1/12 3:37pm - Reply: 'Re: rear brakes'
crossfire1982
Standard Member
- Send Private Message


Cramerton, NC - USA

Vette(s):
black 1982 coupe slate gray interior, 350 crossfire, 1985 fuel pump, Steeroids R&P conversion

Joined: 8/22/2006
Posts: 1094
There are many posts here regarding this same topic by many members. You can use the search funtion to search for all of them. First off, are the rotors below tolerence in thickness?  If they are still in spec then you dont need to replace them to change pads.  If not absolutely necessary to remove them, Id leave them and replace the pads only.  If, on the other hand, it is necessary to get them off the following may help.  Im sure others will chime in as well.  If its pictures of the rivets you are interested in check the post in the link below, perhaps they will help.  The photos will show drilling the rivets with the rotor off of the car but they can be done on the car as well.  Start by center punching  each rivet head then go to a smaller drill bit.  It is not necessary to drill the rivets completely out to get the head off.  Progress up in bit size until the head of the rivet comes off.  Once the heads are off you can see if you can use a punch to drive the rivets out the back side but this may or may not work because the rotor will still be held by the rivet body since it expands in the hole when it is swedged into the assembly.  You can either continue to drill out the rivet body or see if a rubber hammer will encourage the rotors to come off.  Probably you will need to drill out the rivet body as well.  Its aggrivating to get them off but it can be done with a little time, and cutting oil on the bit.  The rivets are NOT hardened and are made of soft material.  It is not necessary to replace the rivets once the rotor is replaced, some prefer to screw them down as in the pictures but most do not, it's not necessary. 

|UPDATED|3/1/2012 12:37:22 PM (AZT)|/UPDATED|


____________________________________

Click for a larger image
Save The Wave


 Reply Reply  Quote Reply w/Quote
3/2/12 9:30am - Reply: 'Re: rear brakes'
kwoody
Former Member
- Send Private Message


Tucson, AZ - USA

Vette(s):
1982 Black/Tan Leather Build Code C09E Bronze TTop CrossFire Fuel Injection L83 85 Fuel Pump Auto Axle 2.72 Firestone Firehawk Indy500

Joined: 7/11/2010
Posts: 415
Hello,

I recently did my first ever brake job on my fronts.  I used the photos mentioned above.  I started with a small bit and worked my way up in size.  Some of the rivets came out pretty easily with a hammer and punch.  I did not have a drill press but, it would have been a lot better if I did.

Be sure to use two wrenches on the brake lines as they are easy to twist if you don't.  I also replaced the flexible brake lines. I installed speed bleeders which makes bleeding the breaks a one person job.

Good luck and all the best from Tucson.

Keith


____________________________________

Nobody ever waves when I'm driving the Explorer.
K Woody
 Reply Reply  Quote Reply w/Quote
 New Topic New Topic Post Reply Reply New Poll New Poll Search     Search Page [1]  
 Forums -> C3 Handling Components
(Moderator: Adam Wartell, Norsky, Adams' Apple)
 

 
Official C3 Vette Registry Community:
Home | Forums | Email | Who's Online | Clubs | Events | Member Stats

Other Official C3 Vette Registry Areas:
Members | Research | Shop | My Account | About C3VR
 

Corvette is a registered trademark of the General Motors Corporation(GM) & Chevrolet Motor Division. Vette Registries, LLC is responsible for all site content (except for member submitted content or where otherwise noted) and does not claim or imply that Chevrolet or GM is responsible for Official C3 Vette Registry content. Vette Registries, LLC is independent from GM and is not affiliated with, sponsored or supported by GM.  Copyright/trademark/sales mark infringements are not intended, or implied and are in fact used to support GM, Chevrolet and Corvette

Official C3 Vette Registry content is Copyright 2001-2017, Vette Registries, LLC. Content may not be reused without written consent. All Rights Reserved. NS

Corvette (Vette) Model Years on this site: 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 30