Topic: Any one have Exploded view of inards of Hurst C Plus shifter
in Forum: C3 Driveline Components
Already a Member?
Click Here to Login
Not yet a Member?
Click Here to Register for Free!
I have been rebuilding my 4 speed transmission, it's all together and I also took apart my Hurst C Plus shifter. The identification on the shifter is 3915403V. I reassembled it and can not get it into reverse, even after aligning the unit with the special round tool. I think I did something wrong in reassembling the small thin metal plates. Does anyone have an exploded view on what is the correct way to assemble all of this?
SPONSOR AD:: (Our Sponsors help support C3VR)

Moderator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 20218
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
I've got a CP shifter here in the garage somewhere. If no-one can provide a pic, or a link to a pic, I'll be happy to dis-assemble this one for pics...
It may be this week-end before I can get to it, but I might be able to do it sooner.

It may be this week-end before I can get to it, but I might be able to do it sooner.
Joel Adams
C3VR Lifetime Member #56
My Link
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
Thanks, I'm off to Europe for a week, so take your time. I would appreciate it. there are different profiles on the thin sheet metal like spacers and I believe this is the issue.

Greensburg, IN - USA
Joined: 9/24/2003
Posts: 5189
Vette(s): Previous: 1984 Coupe, 1988 Maroon Coupe, 1989 Coupe, 2001 Roadster Present: 1967 Stingray Roadster, 1976 Stingray Coupe, 1989 Roadster..
Hey there Jack,
See if this Competition Plus information gets you where ya need to be. Nice talkin with ya last nite some on Chat Nite. Hope you have a great trip Europe!
Tux...
Tuxblacray 2009-03-12 03:48:45
See if this Competition Plus information gets you where ya need to be. Nice talkin with ya last nite some on Chat Nite. Hope you have a great trip Europe!
Tux...

I have that sheet, it helped me getting th elinkage right.
Where I need help is with the insides of the shifter. There are three thin stainless stell/spring steel plates in there. They have different profiles and I want to know the right assembly sequence.
I sent the shifted to Hurst to have them rebuild it.
Is it possible to remove and replace shifter with transmission installed?
Is it possible to remove and replace shifter with transmission installed?
-
Jack, yes you can without removal of the trans. 1. Remove shift cotrol lever knob, spring and "T" handle inside vehicle. 2. Remove console trim plate and seal assy. 3. Raise and support vehicle. 4. Disconnect control rods from shift levers. 5. Remove shift control to support bracket retaining bolts. 6. Remove support bracket to crossover retaining bolts. 7. Remove support assy. from vehicle, then pull down on the control assy. to remove from console boot and vehicle. (This was taken from a 1974 GM Service Manual)
corvette440hp
in Forum: C3 Driveline Components
SPONSOR AD: (Our Sponsors help support C3VR)