Home page
SPONSOR AD

Support our Vendors!  |  Advertise Here

NEW! Check out our new Corvette Quiz!

Topic: Rear end problem

in Forum: C3 Driveline Components


Already a Member?
Login
Not yet a Member?
Register for Free!

Back to top of thread

Re: Rear end problem (6/16)
 9/18/23 10:30pm
Adams' AppleLifetime Member
Lifetime Member
Moderator
Send Private Message

Duncanville, TX - USA

Vette(s):
#1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas


Joined: 11/8/2003
Posts: 20144

If the front diff mount/pinion snubber is completely gone, the front of the diff can twist up/down, and usually the driveshaft will beat on the bottom of the body. It can also allow the halfshafts to run out of whack, making noise. From your description, what you picked up was the front diff mount/snubber. 

Here's a pic of the older style set-up, followed by a diagram of what your car should have. hth 🤠

 

 



______________

Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Re: Rear end problem (7/16)
 9/19/23 5:16pm
DroseLifetime Member
Lifetime Member
Send Private Message

Solon, OH - USA

Vette(s):
1981


Joined: 10/14/2015
Posts: 37

Well the winner was Manchestershark, my passenger side half shaft u-joint broke on the inner side of the wheel and decimated the shock absorber as well as taking out part of the trailing arm.  So now I need to start chasing some parts down.

Thanks for everyones suggestions.  Hard to believe the damage it did in approximately 100 feet and the noises it made.

Thanks again, Dan



______________
Re: Rear end problem (8/16)
 9/19/23 7:54pm
manchestersharkLifetime Member
Lifetime Member
Send Private Message

Equinunk, PA - USA

Vette(s):
1972 conv, 4-speed, 350, 200hp, numbers match, rally wheels, war bonnett yellow w/white top. good condition, nice driver.


Joined: 10/31/2007
Posts: 2403

Yikes! Better call Bairs. They have every piece you may need to repair/replace . Thanks for the update. They also are a huge supporter of this venue and Registry. 



______________


Click on image for full view

Re: Rear end problem (9/16)
 9/19/23 8:17pm
F4GaryGold Member
Gold Member
Send Private Message

Grapevine, TX - USA

Vette(s):
1972 LT-1 convertible with factory air.


Joined: 8/26/2006
Posts: 1420

Drose said:

Well the winner was Manchestershark, my passenger side half shaft u-joint broke on the inner side of the wheel and decimated the shock absorber as well as taking out part of the trailing arm.  So now I need to start chasing some parts down.

Thanks for everyones suggestions.  Hard to believe the damage it did in approximately 100 feet and the noises it made.

Thanks again, Dan



Yikes!  Guess it was obvious once you got under there.  Just keep telling yourself, "it's a hobby!".



______________

   

Re: Rear end problem (10/16)
 9/19/23 9:43pm
manchestersharkLifetime Member
Lifetime Member
Send Private Message

Equinunk, PA - USA

Vette(s):
1972 conv, 4-speed, 350, 200hp, numbers match, rally wheels, war bonnett yellow w/white top. good condition, nice driver.


Joined: 10/31/2007
Posts: 2403

Well, I hope the High Test burns a little leaner on the next take off! 



______________


Click on image for full view

Re: Rear end problem (11/16)
 9/20/23 2:03pm
DroseLifetime Member
Lifetime Member
Send Private Message

Solon, OH - USA

Vette(s):
1981


Joined: 10/14/2015
Posts: 37

Not knowing where Bairs was I had concerns about shipping costs so I goggled them and they are only a 2 hour drive from my house in Cleveland Oh.  So I figure that I will drive my trailing arms and half shafts to them and have it all reconditioned cause I hate doing things twice. 😅



______________
Re: Rear end problem (12/16)
 9/20/23 5:37pm
Steevo
Limited Member
Send Private Message

San Diego, CA - USA

Vette(s):
'73 L48 Coupe, 383, M20, A/C, Electric Windows. Matterhorn White Jet-Glo w/ Dark Blue interior. Rochester, Edelbrock, Blackjack Ceramics, Borlas w/ 2.5" mandrel X over, Cooper Cobras on both OEM Steel and Aluminum Wheels.


Joined: 11/10/2013
Posts: 53

DRose,

Would be a good time in looking into why that U-joint failed, because you have three more back there that can give up the ghost as well (and take out whatever they can reach with it). I replaced all 4, just because the PO had already bought them and never got to it before I bought the project. Spicer brand U-joints was what they were, IIRC. 

Steve



|UPDATED|9/20/2023 2:37:36 PM (AZT)|/UPDATED|


______________

 

 

Re: Rear end problem (13/16)
 9/21/23 4:07pm
Yogi
Limited Member
Send Private Message

WESTLAKE, OH - USA

Vette(s):
1982 Claret red Coupe


Joined: 12/9/2001
Posts: 2

Drose said:

Not knowing where Bairs was I had concerns about shipping costs so I goggled them and they are only a 2 hour drive from my house in Cleveland Oh.  So I figure that I will drive my trailing arms and half shafts to them and have it all reconditioned cause I hate doing things twice. 😅


Interested in what you are going to have done with the trailing arms and half shafts over there. I knew they were in PA, but didn't know they did re-builds. That makes them only 3 hours away from me.



|UPDATED|9/21/2023 1:07:27 PM (AZT)|/UPDATED|
Re: Rear end problem (14/16)
 9/21/23 4:19pm
DroseLifetime Member
Lifetime Member
Send Private Message

Solon, OH - USA

Vette(s):
1981


Joined: 10/14/2015
Posts: 37

I agree and I am going to replace all four u-joints and have them install the locks on the u-joint bolts.  It appears I lost a bolt on one of the U-joints and then it came apart and just tore apart my shock on that side, some fiberglass in the storage pocket and took some metal off the trailing arm. Actually a lot of damage.



______________
Re: Rear end problem (15/16)
 9/21/23 4:35pm
DroseLifetime Member
Lifetime Member
Send Private Message

Solon, OH - USA

Vette(s):
1981


Joined: 10/14/2015
Posts: 37

If you have not already you should go to there webb site and see what they offer.  I am going to have them recondition my trailing arms. They give you a whole list of what they do and you should read it, its impressive.  You have to figure they have all the parts and knowledge to rebuild the entire car and in my case the best prices for what I need done.  They also give you a number to call and you can discuss your problem with a knowledable person who knows all about Corvettes, extremely helpful, you couldn't ask for more.

I am also going to have them look at my half shafts and I will replace all four u-joints, in addition I will actually have a functioning parking brake because of rebuilding my trailing arms.

No shipping because they are so close and look at all the fun I am going to have.  LOL



______________
Re: Rear end problem (16/16)
 9/21/23 8:09pm
manchestersharkLifetime Member
Lifetime Member
Send Private Message

Equinunk, PA - USA

Vette(s):
1972 conv, 4-speed, 350, 200hp, numbers match, rally wheels, war bonnett yellow w/white top. good condition, nice driver.


Joined: 10/31/2007
Posts: 2403

Just as a F.Y.I. to all who may be interested, Bairs is the place to go for Expert rebuilding of any mechanical problem. They are CORVETTE PEOPLE.  They only work on Corvettes. Take a ride to their facility and lay eyes on the business. An exceptional customer relations mentality. Last time I was there, it was "Nothing but Corvettes". 



______________


Click on image for full view

Our Sponsors help support C3VR