Home page
SPONSOR AD

Topic: replace headight switch

in Forum: C3 Electrical

replace headight switch

Posted: 12/24/07 12:55pm Message 1 of 6
Former Member
Send PM
Suffolk, VA - USA
Joined: 3/18/2006
Posts: 47
Vette(s): 1978 Silver anniversary model, two tone, L-48, auto, Oyster interior, numbers matching, body work completed 2008 and painted back original colors

I need to remove headlight switch and wiper on-off lever. Cannot see how to do from front. Remove dash? Hopefullt not!

need directions! Thanks,
Bick



SPONSOR AD:: (Our Sponsors help support C3VR)

replace headight switch

Posted: 12/24/07 1:55pm Message 2 of 6
Former Member
Send PM
Fayetteville, NC - USA
Joined: 2/13/2005
Posts: 244
Vette(s): 1968 Corvette Convertable, 4 spd, 350 SB, Daily Driver
My '68 requires the removal of the gage cluster.  I do not have to pull off the dash to do that.  The differences between our cars should not be that much, a few screws and my gage clusters are loose.  Getting the speedometer/tach assembly past the steering wheel is tough, so I would recomend you loosen the switch and remove it without pulling the assembly completely out.  The wiper switch cannot be changed without removing the center consol panel.
 
Good luck, take your time...



replace headight switch

Posted: 12/24/07 1:57pm Message 3 of 6
Former Member
Send PM
Suffolk, VA - USA
Joined: 3/18/2006
Posts: 47
Vette(s): 1978 Silver anniversary model, two tone, L-48, auto, Oyster interior, numbers matching, body work completed 2008 and painted back original colors
forgot to mention year is 1978


replace headight switch

Posted: 12/24/07 2:12pm Message 4 of 6
Lifetime MemberLifetime Member
Send PM
Eastern Oklahoma County, OK - USA
Joined: 1/3/2006
Posts: 1560
Vette(s): 1980 Black L48 T-Tops
78 - 82 is easier.  you just remive the air pipe across to the side vent, reach up inside and look for the push button on the switch bottom.  When you depress it, you will be able to pull the stem all the way out.  Then use a large flat blade screwdriver to remove the facia.  Pull the switch out from the back.  It has 2 plug ins and 2 hoses.  The hoses have to go on the same way they came off.  If you have the time, take the female plugs out of their housing and tighten them up a bit by using needle nose to lightly crimp down on each round side.  DONT CRUSH!  Then reinstall reverse of how it came out.

GOOD LUCK!!

Merry Christmas and Happy New Year!!!



replace headight switch

Posted: 12/24/07 2:34pm Message 5 of 6
Former Member
Send PM
Suffolk, VA - USA
Joined: 3/18/2006
Posts: 47
Vette(s): 1978 Silver anniversary model, two tone, L-48, auto, Oyster interior, numbers matching, body work completed 2008 and painted back original colors
Dennism
Thanks!
How about the wiper switch?
Bick



replace headight switch

Posted: 12/24/07 2:42pm Message 6 of 6
Lifetime MemberLifetime Member
Send PM
Eastern Oklahoma County, OK - USA
Joined: 1/3/2006
Posts: 1560
Vette(s): 1980 Black L48 T-Tops
I haven't taken mine out yet however, I think if you dropped the column, pulled the gauge cluster (speedo & tach), then you should be able to go in from the side HOWEVER, I personally haven't done it yet.

I'll check the shop manual for advice.  I just got mine, bought it off ebay.





in Forum: C3 Electrical


SPONSOR AD: (Our Sponsors help support C3VR)