Topic: turn signal question
in Forum: C3 Electrical
Already a Member?
Click Here to Login
Not yet a Member?
Click Here to Register for Free!
My turn signals just stop working. When I first start the car and take off the turn signals work. Then after a little while I go to use the turn signal and no blinking signal just a steady turn light (no blinking). I checked all the lights and all come on as they are supposed to, except the turn signals don't blink.
I suspect the flasher but would like some experienced opinions and suggestions.
thanks for any help.
I suspect the flasher but would like some experienced opinions and suggestions.
thanks for any help.
SPONSOR AD:: (Our Sponsors help support C3VR)

Moderator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 20214
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
I'd suspect the flasher, too. 

Joel Adams
C3VR Lifetime Member #56
My Link
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
You might want to try your emergency flashers. If they work steady than I would replace flasher. Easy fix.
My 78 did the same thing-- ended up replacing the bulb holders to fix the problem ( the springs that pushed the connector contact to the bulbs was not doing its job, seems the heat stops it from working until it cooled down)
Annicorvette
Lifetime member # 35
Thanks
This group has never dissapointed me when trying to get an answer to a question.
I hope I can help someone someday as much
Thanks again everyone.
This group has never dissapointed me when trying to get an answer to a question.
I hope I can help someone someday as much
Thanks again everyone.
Make sure you battery/charging system voltage is staying up where it belongs. Low voltage will cause this as well. But it probably is the flasher as long as all of the light come on properly.
kstyer 2008-06-26 20:16:31
Flashers, when working properly, operate based on the amount of amperage going through them. Too little they don't blink. Too much the blink off very quickly.
Newer electronic flashers work just the opposite except they don't stop with high lods, just blink very fast with low amps.
Low amps is usually a bad bulb or poor connection.
I thought I would try replacing the flasher first and see if that fixes the problem.
I have an assembly manual and it looks like the flasher is located behind the glove compartment and you have to remove the "box" to get to it.
Is this right or can you get to it from underneath?
thanks for the help
I have an assembly manual and it looks like the flasher is located behind the glove compartment and you have to remove the "box" to get to it.
Is this right or can you get to it from underneath?
thanks for the help

Moderator
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 20214
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/
Am-Fm/map light National/Regional/Chapter NCRS "Top Flight"
#2-1985 Bright Red/Carmine Cp.L-98/auto
Member: NCRS, NCRS Texas, Corvette Legends of Texas
I believe you can get it just reaching up under the gbox, about the center of it, but it may be to one side.

Joel Adams
C3VR Lifetime Member #56
My Link
(click for Texas-sized view!) NCRS
"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"
in Forum: C3 Electrical
SPONSOR AD: (Our Sponsors help support C3VR)