Home page
SPONSOR AD SPONSOR AD

Topic: Rear Spring

in Forum: C3 Engines, Driveline and Handling


Rear Spring

Posted: 10/5/06 8:07am Message 1 of 4
Former Member
Send PM
Oakton, VA - USA
Joined: 12/27/2005
Posts: 28
Vette(s): 1968 L-71 Coupe
During a discussion with another C3 owner he asked if I had replaced the stock rear spring on my 68 coupe with an aftermarket unit containing spring clips. He further stated that the OEM units are inherently dangerous as they can spin or twist. Does anyone know what he's talking about? Smile


SPONSOR AD:: (Our Sponsors help support C3VR)

Rear Spring

Posted: 10/5/06 8:42am Message 2 of 4
Profile Pic
Lifetime MemberLifetime Member
Moderator
Send PM
Duncanville, TX - USA
Joined: 11/8/2003
Posts: 20225
Vette(s): #1-1974 L-48 4spd Cp Med Red Metallic/Black deluxe int w/AC/tilt/tele./p/w-p/b/ Am-Fm/map light National/Regional/Chapter NCRS "Top Flight" #2-1985 Bright Red/Carmine Cp.L-98/auto Member: NCRS, NCRS Texas, Corvette Legends of Texas
[QUOTE=RJKEELER] During a discussion with another C3 owner he asked if I had replaced the stock rear spring on my 68 coupe with an aftermarket unit containing spring clips. He further stated that the OEM units are inherently dangerous as they can spin or twist. Does anyone know what he's talking about? Smile[/QUOTE]

                         "inherently dangerous"..." spin or twist"

Someone should notify GM of this...they built over a half a million Sharks(not to mention the mid-years) with that spring design!!!

Theez I have never heard of! I know most of the aftermarket springs do have clamps around the leaves, but GM never did it on the originals. If the leaves are stacked properly, and the assembly bolted together properly, there is no danger of a problem.

How th' heck can the spring "twist", or "spin"?? It can't, unless the lower bracket that holds the spring to the diff. cover is loose, and that's not a design flaw...that's an installation error.
my 2c


Joel Adams
C3VR Lifetime Member #56    

My Link


(click for Texas-sized view!)
             NCRS

"Money can't buy happiness -- but somehow it's more comforting to cry in a CORVETTE than in a Kia"

Rear Spring

Posted: 10/5/06 11:17am Message 3 of 4
Former Member
Send PM
Oakton, VA - USA
Joined: 12/27/2005
Posts: 28
Vette(s): 1968 L-71 Coupe
My thoughts exactly! I think someone sold him a bill of goods with a new spring.


Rear Spring

Posted: 10/5/06 7:42pm Message 4 of 4
Profile Pic
Lifetime MemberLifetime Member
Moderator
Send PM
CUYAHOGA FALLS, OH - USA
Joined: 12/2/2003
Posts: 6424
Vette(s): 1975 C3 Red, T-Tops, Black Interior. All I need is time and money! Getting there!
Some leaf springs will have one or more leafs rotate slightly from the center point.  Then the leafs don't line up quite right.  One leaf may stick out from the others by 1.4 inch or so.  This is only cosmetic.  It won't affect the operation of the spring.  The straps prevent the springs from doing this.   But the way the spring are mounted on our Vettes, this is very minor, and not worth metioning.   Some vehicles can allow the sprng leafs to move almost an inch out of line at the end of the leafs.  But these are two leaf systems with a narrow axle tube.  Not our problem.


in Forum: C3 Engines, Driveline and Handling


SPONSOR AD: (Our Sponsors help support C3VR)