Home page
SPONSOR AD SPONSOR AD

Topic: Replacing Steel Brake Lines

in Forum: C3 Engines, Driveline and Handling


Replacing Steel Brake Lines

Posted: 7/6/10 8:43am Message 1 of 6
Former Member
Send PM
Joined: 6/27/2010
Posts: 21

I am replacing the calipers, brake hoses and master cylinder on my ’70 (with 4-speed).  I’m considering replacing all the steel lines as well.

 

1) Relative to the brake line on the left side frame rail: (a) I can cut the brake line clips to get them off, but what's the trick to putting new ones on without lifting the body?  (b) If the car is on jack stands, does this provide enough height and clearance to install a new line?

2) If I purchase a brake line kit from one of the well known Corvette parts suppliers, how well do these pre-bent lines fit?

3) Are there any other significant issues I may encounter?

4) Any other advice?

Thanks

Dan

Dan7772010-07-06 14:51:48


SPONSOR AD:: (Our Sponsors help support C3VR)

Replacing Steel Brake Lines

Posted: 7/6/10 9:33am Message 2 of 6
Profile Pic
Former Member
Send PM
Elkhart, IN - USA
Joined: 10/7/2007
Posts: 209
Vette(s): 1975 Red T-Top 1972 Red Convertible
I just replaced the front to back on my 72 with ss line. It is not that hard just take your time and it will fit fine. You can get kits from most Corvette parts suppliers. I got mine form Muskegon Brake. Make sure that you get the two brass fittings for the rear crossover lines. They will crack when you take them appart. Censored
 
 



Replacing Steel Brake Lines

Posted: 7/6/10 6:36pm Message 3 of 6
Profile Pic
Lifetime MemberLifetime Member
Send PM
Waterford, MI - USA
Joined: 9/13/2002
Posts: 1755
Vette(s): 1973 Red coupe
The brake lines can be replaced with some time and a little bending. The stainless steel lines are the way to go. The fittings need to be tightened a little more then the standard steel lines to get them to seal correctly. Just make sure you have good quality wrenches or you could round off the fittings.


Brian - NCM Lifetime Member

73 coupe L48, Flat-top pistons, Performer RPM Heads, Crane Cam and roller rockers, Holley 650 vac sec. Performer intake,
3.55 gear BTO 200-4R trans,
Leather seats, Seatbelt Plus 3point seatbelts, Pioneer CD player
Magnaflow Exhuast System

Dewitt radiator and dual electric fans
Borgeson Steering box
 


Replacing Steel Brake Lines

Posted: 7/8/10 9:18am Message 4 of 6
Former Member
Send PM
Mounds View, MN - USA
Joined: 5/24/2007
Posts: 1031
Vette(s): 70 LT1 coupe, 69 350 HP coupe, 69 390HP 427 coupe, 71 LS5 convert, 85 coupe, 93 coupe
I agree with the part about ease of installation, but very much disagree about SS lines.  They are more expensive, harder to flex, and prone to leaks.  They last longer, but your originals lasted 30 years.

Larry



Replacing Steel Brake Lines

Posted: 8/9/10 3:23am Message 5 of 6
Former Member
Send PM
Joined: 6/27/2010
Posts: 21
Thanks guys.
Dan


Replacing Steel Brake Lines

Posted: 8/9/10 5:54pm Message 6 of 6
Profile Pic
Former Member
Send PM
edgwood, MD - USA
Joined: 11/1/2007
Posts: 736
Vette(s): 1975 convertible,with the hard top and power streering.it a 350 L48 with auto trans. the color is light blue.
I just replace the line that runs along the left frame rail ,it was a major pain .my advice if you do this do it on a lift I did mine with the car on jackstands.To fish the line around  the frame and body I bent the line as I moved along.Going around the frame to the rear wheels gets tricky.But with patients it can be done.I put steel line back on mine because it was easier to work with.
                           Rick


in Forum: C3 Engines, Driveline and Handling


SPONSOR AD: (Our Sponsors help support C3VR)