Topic: Who wants to build a bleeder?
in Forum: C3 General Discussion
Already a Member?
Click Here to Login
Not yet a Member?
Click Here to Register for Free!
Former Member
Send PM
Yelm, WA - USA
Joined: 7/12/2007
Posts: 356
Vette(s): 1979 L82 4 speed Scat 383 crank 190 cc Procomp Aluminum Heads 202 160 stainless valves GM Powder metal rods Speedpro H860CP Hypereutectic pistons 280 cam hydralic HEI Pro comp 1.6 roller rockers Mighty Demon 750 Sanderson CC1AP Hedders.
[QUOTE=Norsky]My understanding of how to use them is to have fluid in the MC and the sprayer. Putting pressure on the sprayer forces fluid through the brake system without worrying about the MC going dry.[/QUOTE]
I don't know which way is better fluid or no fluid? Initially I was going to have fluid in the sprayer but then I thought the homeade system might pump air bublles into the brake fluid so I chickened out.
Looks like the sheet metal I used is already starting to show signs of corrosion. A nice 1/8 or thicker piece of Aluminum would be the trick. I also thought about making my own gasket outa cork but I would have had to buy the roll and pushed the cost of materials up. A new MC gasket was like 5 bucks so I used the old one. I might get brave and try it with fluid in the sprayer next time
Updated pics
SPONSOR AD:: (Our Sponsors help support C3VR)
I think fluid in the sprayer is the way to go.
Then you never need to check the MC.
Use clear plastic tube to make sure you are putting air bubbles into the MC.
And I think pressure is better than suction.
Save the Wave!
Support the National Corvette Museum
Support the National Corvette Museum
Lifetime MemberSHELBYVILLE, TN - USA
Joined: 7/5/2002
Posts: 3942
Vette(s): 1976 L48 auto
1978 L82 4speed
1994 LT1 6speed
1978 L82 4speed
1994 LT1 6speed
this is jimmy jr, years ago, i did basically the same thing here, i took an old mc cover, drilled a hole in it, and put a bolt on valve stem(a tire valve stem, that has a nut on the bottom side, along with a rubber washer for a seal)... i would position the valve stem over the resivoir i wanted to bleed, just using air.... worked pretty good, just had to keep an eye on the fluid level, sooo would just take a couple shots of air at a time.... basically did this to just get the brake fluid flowing so i could gravity bleed the system...
StingrayJim 
NCM Lifetime Member #1936
Stingray's '76���������������������������� StingrayJr's '78���������������������������Lil Red '94 
(click each one to see a bigger version)
Dave, In my quest for el-cheapo I didn't consider a purchased cover, I have 12 bucks in it so far and trying to stay cheap
Mike, that clear hose is a good idea. I figured any way I do it i'm going to spill some. I plan to place a plastic bag under it and see if that will catch most of it. When I get my camera i'll post pictures of this gizmo on the forum.
How's that little dog that got the surgery getting along. There just isn't anything better than dogs and kids.
Jim, (norsky) I know what ya mean about the cold, We've had a bunch of it here in Missouri and I know also that yous guys up north have had it even worse.
I took one side of my pole barn /w gravel floor and layed down plastic, then I layed down OSB strand board over the plastic. I then surrounded the 78 with plastic and buttoned everything up (the ceiling was there with the loft). I lighted the place, got my tool chest and parts-washing tub in there and thought I was good-to-go. The space heater in the "cocoon" will raise the temp only 10 degrees above outside temps.
so, all my projects will have to wait till it warms abit.
so, all my projects will have to wait till it warms abit.I was a-think-n.....thick plexiglass might work for a cover. Hmmmmmm
Rich, the cover is in the mail.
As for spilling fluid, I've used mine at least 10 times and I've got it down to where I don't spill a drop at the master, and that's with the goofy flat cover provided by Motive but held in place with 2 clamps. DON'T fill the master up to the top before hooking up the bleeder. 1/2" below the rim works fine, and when you're done it will still be 1/2" down preventing spilling.
Thanks for asking about Mickey. He's doing great. Got his stitches out Tuesday and finally got a bath today(pheew!). Hoping to get the hip done shortly.
Well I received the mc cover in the mail today from Mike,,,thanks alot Mike, it's a nice cover for this project.
I'm going to take your advise and keep the fluid 1/2" below the top. If I keep the system tight, I guess the air in the mc will never intrain into the fluid which I suppose is why the fluid is special in the first place.
I'll see if I can get some time this week and get it all together.
Thanks abunch....Rich.....(pm sent about Mickey)
in Forum: C3 General Discussion
SPONSOR AD: (Our Sponsors help support C3VR)