Home page
SPONSOR AD

Topic: 83 collector edition hatch release cable

in Forum: C3 Interior

83 collector edition hatch release cable

Posted: 12/15/15 10:39pm Message 1 of 5
Profile Pic
Former Member
Send PM
Tuttle, OK - USA
Joined: 12/15/2015
Posts: 18
Vette(s): 1982 Corvette Collector Edition
Just purchase this c3, and having problem with the cable that release that allows the hatch to be open. When the handle is pull, nothing happens.


SPONSOR AD:: (Our Sponsors help support C3VR)

Re: 83 collector edition hatch release cable

Posted: 12/16/15 11:43am Message 2 of 5
Profile Pic
Former Member
Send PM
Gig Harbor, WA - USA
Joined: 10/2/2014
Posts: 405
Vette(s): 1973 L82 4 Speed Coupe - Very original, well documented driver/survivor. 2016 Bend Regional NCRS Top Flight.
First thing I would check is to see if the cables are connected and the latches are functioning. ..................The first cable with the handle on it goes back to the first latch on the drivers side. That latch is connected to the passenger side latch by another cable that goes between the two. Not sure if you have to remove the rear compartment shade or not, but both latches and cables should be visible from underneath the black plastic surround. You'll have to crawl back there and observe while someone pulls the cable. ...................... If both cables and latches are working, make sure both latches are moving far enough to clear the two metal strikes that come down from the glass hatch. ......................... If all that seems to be in order, it might be that your gas shocks are shot and do not have enough ooooomph to raise the glass. ....................... If this seems to be the case, have your assistant pull the cable while you press up from underneath the glass. What ever you do be VERY CAREFUL when opening and closing the hatch !!! That glass is no longer produced and is very expensive to find a new piece. .................... See what the first couple steps above look like and let us know what you find. Good luck !!

|UPDATED|12/16/2015 11:43:12 AM (AZT)|/UPDATED|



John Sigmund
valkman57@sbcglobal.net
NCRS Member 61302
NW NCRS Chapter Member



Duct tape is the new Black !!

Re: 83 collector edition hatch release cable

Posted: 12/16/15 9:20pm Message 3 of 5
Profile Pic
Former Member
Send PM
Tuttle, OK - USA
Joined: 12/15/2015
Posts: 18
Vette(s): 1982 Corvette Collector Edition
I check the cable and found the cable had come disconnect from the bracket behind the driver seat. The threads on the plastic portion are worn out and not sure on how I'm going to fix it. Is there anywhere I can get one to replace it.


Re: 83 collector edition hatch release cable

Posted: 12/17/15 12:04pm Message 4 of 5
Profile Pic
Former Member
Send PM
Gig Harbor, WA - USA
Joined: 10/2/2014
Posts: 405
Vette(s): 1973 L82 4 Speed Coupe - Very original, well documented driver/survivor. 2016 Bend Regional NCRS Top Flight.
Not sure if any of the Corvette suppliers carry much CE stuff. ZIP Corvette has the replacement gas shocks for the hatch but no latch hardware. Your best bet might be EBay, there's usually some CE hatch hardware listed. Just do a search for 1982 Collector Edition. You'll probably also see the $$$ of used hatch glass there. Good luck and keep us posted.


John Sigmund
valkman57@sbcglobal.net
NCRS Member 61302
NW NCRS Chapter Member



Duct tape is the new Black !!

Re: 83 collector edition hatch release cable

Posted: 12/27/15 9:54am Message 5 of 5
Profile Pic
Former Member
Send PM
Victor, NY - USA
Joined: 7/12/2004
Posts: 6841
Vette(s): 2004 Commemorative Edition Coupe, Auto w/HUD. 13K miles in 2015. Sold 1982 Red Coupe
I believe the '84 Corvette has the same latch and cable.


 
Save the Wave!
Support the National Corvette Museum   

in Forum: C3 Interior


SPONSOR AD: (Our Sponsors help support C3VR)