WORKSHOP TOOLS

1)DRILL PRESS: A tall upright machine useful for suddenly snatching flat
metal bar stock out of your hands so that it smacks you in the chest and
flings your drink across the room, splattering it against that freshly
painted part you were drying.

2)WIRE WHEEL: Cleans paint and rust off bolts and then throws them somewhere under the workbench with the speed of light. Also removes skin from knuckles
and hard-earned work calluses in about the time it takes you to say,
"$hit...."

3)ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you burn the surrounding area.

4)PLIERS: Used to round off bolt heads.

5)HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion, and the more you attempt to influence its course, the more
dismal your future becomes.

6)VICE-GRIPS: Used to round off bolt heads. If nothing else is available,
they can also be used to transfer intense welding heat to the palm of
your hand.

7)OXYACETYLENE TORCH: Used almost entirely for lighting various flammable
objects in your workshop on fire. Also handy for igniting the grease
inside the wheel hub you want the bearing race out of.

8)WHITWORTH SOCKETS: Once used for working on older British cars and
motorcycles, they are now used mainly for impersonating that 9/16 or ½
socket you've been searching for the last 15 minutes.

9)HYDRAULIC FLOOR JACK: Used for lowering a car to the ground after you
have installed your new disk brake pads, trapping the jack handle firmly
under the bumper.

10)EIGHT-FOOT LONG DOUGLAS FIR 4X4: Used to try to lever a car upward off a
hydraulic jack handle.

11)PHONE: Tool for calling your neighbour to see if he has another
hydraulic floor jack.

12)TWEEZERS: A tool for removing wood splinters caused by the douglas fir 4X4.

13)"SNAP-ON" GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog-sh*t off your boot.

14)E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known
drill bit that snaps off in bolt holes you couldn't use anyway.

15)TWO-TON ENGINE HOIST: A tool for testing the tensile strength on
everything you forgot to disconnect.

16)CRAFTSMAN 1/2 x 16-INCH SCREWDRIVER: A large pry-bar that inexplicably
has an accurately machined screwdriver tip on the end opposite the handle.

17)AVIATION METAL SNIPS: See hacksaw.

18)TROUBLE LIGHT: The home mechanic's own tanning booth. Sometimes called a
drop light, it is a good source of vitamin D, "the sunshine vitamin,"
which is not otherwise found under cars at night. Health benefits aside,
it's main purpose is to consume 40-watt light bulbs at about the same
rate that 105-mm howitzer shells might be used during, say, the first
few hours of the Battle of the Bulge. More often dark than light, its
name is somewhat misleading.

19)PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style
paper-and-tin oil cans and splash oil on your shirt; but can also be
used, as the name implies, to strip out Phillips screw heads.

20)AIR COMPRESSOR: A machine that takes energy produced in a coal-burning
power plant 200 miles away and transforms it into compressed air that
travels by hose to a Chicago Pneumatic impact wrench that grips rusty
bolts last over tightened 58 years ago by someone with an even bigger compressor and neatly
rounds off their heads.

21)PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket you needed to remove in order to replace a 50 cent part.

22)HOSE CUTTER: A tool used to cut hoses too short.

23)HAMMER: Originally employed as a weapon of war, the hammer nowadays is
used as a kind of divining rod to locate the most expensive parts not
far from the object we are trying to hit.

24)MECHANIC'S KNIFE: Used to open and slice through the contents of
cardboard cartons delivered to your front door; works particularly well
on contents such as seats, liquids in plastic bottles,
collector magazines, refund checks, and rubber or plastic parts.

25)EXPLETIVE: A balm, usually applied verbally in hindsight, which somehow
eases those pains and indignities following our every deficiency in
foresight.

Adams' Apple38683.6946990741

I know it's late and I've had a long day. But I'm sitting here reading this and I realize that to a degree it sums up my life in the shop!

This seem like a very accurate list.  Amazing.

       

Somebody has been peeking in my garage.    

I especially liked the mention of Whitworth wrenches. My daughters boyfriend was over the other day helping me work on a Puch motercycle engine. I asked him to get me the box with these wrenches in it. He looked puzzled. I told him they were next to the TORX /Clutchead / & old German Wrenches that were going to take over the world oneday but never quite made it. Anyone that has Whitworth wrenches laying around falls into one of these catagories: older, bought them for a specific use. enheirited them, or found them in a box of tools bought at some sort of sale.
Thanks for the laugh I have copied your thread and am going to send it to a machinist friend of mine. He will definately love it!

Now thats damn funny. I have to wonder however why there was no mention of the Hammer also being an effective "finger tip circulation tester"
Glenn

Also, no mention of Duck Tape.  Between that and bailing wire, I can fix just about anything.

Larry

Hey Glenn, we used to call a hammer a "pressure calibrator".

Dejablu38681.7180324074

very funny but sadly very true.