Differential Removal?? - Forums - Official C3 Vette Registry

SPONSOR AD

Support our Vendors! | Advertise Here

Topic: Differential Removal??

in Forum: C3 Driveline Components

Already a Member?
Login
Not yet a Member?
Register for Free!

Differential Removal?? (1/10)
12/18/08 9:09pm

Phill's Vette

Lifetime Member
Send Private Message

Apache Junction, AZ - USA

Vette(s):
1982,150K,Renegade CFI,Hooker Side Pipes,85 fuel pump,Bilsteins,HD suspension, Aluminum radiator, SharkBar/w 5-Point Restraints. 3:73 gears coming soon.

Joined: 10/15/2006
Posts: 285

MERRY CHRISTMAS C3VR!!!

I am removing my stock differential and replacing with a new rebuilt unit with 3.73 gears -yeah, I know I must be crazy... but if I don't like it I will have it re-geared.

Anyway, anything I need to know about removal/installation, what bushings I should replace etc.? I will fill it with the GM specified fluid with a bottle of the GM conditioner. I am also replacing all 6 U-joints while I'm there. I do have the Service and AIM manuals along with several other books to help.

I am planning this at the same time I remove the old duel exhaust for the new Hooker side pipes.
Any advice as always -always greatly appreciated!

Thanks!

Our Sponsors help support C3VR

Differential Removal?? (2/10)
12/19/08 10:51am

VetteSpecialties
Former Member
Send Private Message

Mounds View, MN - USA

Vette(s):
70 LT1 coupe, 69 350 HP coupe, 69 390HP 427 coupe, 71 LS5 convert, 85 coupe, 93 coupe

Joined: 5/24/2007
Posts: 1031

There is a bushing set by the pinion. It is about $20.00 for a new one and just bolts in. The process is pretty obvious once you start.

Larry

Differential Removal?? (3/10)
12/20/08 7:16am

lukesvette

Lifetime Member
Send Private Message

HOWELL, NJ - USA

Vette(s):
1979, Targa Blue (72 Color), Pace Car rear spoiler, L88 hood, Dark blue factory interior, 525HP 406, HD 700R4, 370 gears,Steeroids, composite rear spring, TT IIs wrapped in T/A Radials.

Joined: 5/18/2004
Posts: 6812

Quick Tip

- If you drop the rear cross member that the top of the pumpin is bolted into, you can lower it down and out as one unit with a floor jack since you'll have the half shafts, spring and struts out of the way already.

Many folks have cut a hole in the rear compartment floor over the 4 cross member to diff mounting bolts to access them. This alleviates the need and you can spruce up the rear cross member while you're at it. Wink

Soak the 2 crossmember to chassis bolts with penetrating fluid before you start.

Good luck. Smile

Paul

LukesVette2008-12-20 07:17:34

______________

LukesVette Homepage
Veteran of Operation Iraqi Freedom
101st Airborne(AirAssault!)
God Bless America
Support Our Troops

Differential Removal?? (4/10)
12/20/08 3:32pm

Sarge81

Lifetime Member
Send Private Message

WEST SENECA, NY - USA

Vette(s):
1981 Blue Ice Met. w/pearl ghost flames TKO500 5speed. LS1 Swap 3.45 Dana 44.

Joined: 12/3/2001
Posts: 2379

'80-'82 diffs aren't bolted in like '79 and earlier diffs.

There is one mount at the front on the diff. like '79 and previous, and a mount at each end of the "batwing" that bolt to the left and right frame rails. Way easier to remove these late units vs. the older ones. Plus they are aluminum which is lighter than the previous cast iron diffs.

With the use of a lift I can R&R my diff in 4hrs. Have a friend help you lower the unit out of the car cause it is still a little "weighty" an ackward due to the span of the "batwing."

______________

GEN III 5.7L "LS6" Engine swap
TKO500 5 spd.

3.54 Dana 44

'69 "N11" Sidepipes
Borgeson Steering Box
Born 8/1981
Sequence #3975

Click here to see more pics of my Vette on CarDomain.

Lifetime Member #26

Differential Removal?? (5/10)
12/21/08 6:30am

lukesvette

Good point Sarge - didn't even realize they had a different set up. Apologies for the confusion Embarrassed

______________

LukesVette Homepage
Veteran of Operation Iraqi Freedom
101st Airborne(AirAssault!)
God Bless America
Support Our Troops

Differential Removal?? (6/10)
12/21/08 4:06pm

Phill's Vette

Thanks guys!
I'll take pics as I go for anyone needing them in the future.

Differential Removal?? (7/10)
12/21/08 6:39pm

Jeffm
Former Member
Send Private Message

Sebago Lake, ME - USA

Vette(s):
1978 Silver Anniversary L82 4spd (M21) Red Leather. Pace Car is in the hands of a new caretaker.

Joined: 2/15/2007
Posts: 964

I'll be watching this as I plan to do some rearend work this winter also. Got a new composite spring and the diff leaks and makes noise when turning from a stop so I might just drop the whole thing too. Picked up a lightly used mid height lift so things should be easier.

Differential Removal?? (8/10)
1/5/09 4:39pm

rick jay
Former Member
Send Private Message

Liverpool, NY - USA

Vette(s):
72 coupe, 350 4 spd, modified motor, exhaust, tires & wheels. '91 ZR1, modified exhaust.

Joined: 1/21/2003
Posts: 82

I've dropped the diff. in my '72 a couple of times and for me it was better to drop the "batwing" with the diff. I used a floor jack which worked really well and of course a good set of jackstands. Using a mid-lift would work even better, I imagine. Pics always help, I took a few while I was working on mine.
Good luck.

Differential Removal?? (9/10)
1/5/09 8:58pm

Karmel77

Lifetime Member
Send Private Message

Clarksville, TN - USA

Vette(s):
1977 L48 T Top, Dark Blue

Joined: 10/22/2005
Posts: 266

I did mine a few years ago, the wife help me steady it while I jacked it into place with a floor jack. I would recommend getting the shock mount removal tool. I just got a bigger hammer!! That cost me an extra 60 bucks I didn't count on!!

Good luck!!

Mel

______________

Mel
Lifetime Member #90

Differential Removal?? (10/10)
1/6/09 5:42am

crossfire1982
Former Member
Send Private Message

Cramerton, NC - USA

Vette(s):
black 1982 coupe slate gray interior, 350 crossfire, 1985 fuel pump, Steeroids R&P conversion

Joined: 8/22/2006
Posts: 1094

Phill, Id be interested in seeing the pictures. I have some rear end work that needs to be done as well and have been reluctant to tackle the differential removal.

Our Sponsors help support C3VR